Electronicdesign 20893 Link Flexliion Promo
Electronicdesign 20893 Link Flexliion Promo
Electronicdesign 20893 Link Flexliion Promo
Electronicdesign 20893 Link Flexliion Promo
Electronicdesign 20893 Link Flexliion Promo

High-Density Spine-Like Li-ion Battery Flexes, Twists, Conforms

Feb. 24, 2018
Researchers have designed and tested a battery with a mechanical design that mimics the spine of vertebrates, yielding a very flexible cell with capacity close to that of a conventional rigid cell.

Rechargeable batteries based on lithium-ion (Li-ion) chemistry are the preferred energy-storage cell in applications such as wearables, flexible displays, and even transdermal patches. However, providing extreme flexibility while retaining their high energy density has been a challenge. To overcome this problem, a 14-member research team led by Prof. Yuan Yang of the engineering school at Columbia University (New York) modeled, designed, built, and fully evaluated a configuration that emulates the spine of vertebrates, while providing 85% of the energy density of a prismatic Li-ion cell with equivalent volume.

Their design, which was “inspired” by the suppleness of the spine as observed when doing sit-ups and other exercises, has excellent mechanical flexibility along with stable output voltage even while flexing. The physical implementation is scalable to longer lengths and larger capacities.

Like the biological spine configuration on which it’s based, this battery prototype has a thick, rigid segment that stores energy—the electrodes (analogous to the vertebrae) are wound around a thin, flexible part (the “marrow”) that connects the vertebra-like stacks of electrodes together (see figure). Yang noted that “because of the high proportion of the active materials in the whole structure, our spine-like battery shows very high energy density—higher than any other reports we are aware of.”

In the flexible spine-like battery, the vertebrae correspond to thick stacks of electrodes and soft marrow corresponds to unwound part that interconnects all the stacks (a). To fabricate the spine-like battery, multilayers of electrodes were first cut into designed shape; then strips extending out were wound around the backbone to form spine-like structure (b). (Credit: Yuan Yang/Columbia Engineering)

To build the battery, the team cut the conventional anode/separator/cathode/separator stacks into long strips with multiple “branches” extending outward at 90 degrees from the “backbone.” Next, they wrapped each branch around the backbone to form thick stacks for storing energy, like spinal vertebrae. The battery’s energy density is a function of the ratio of the longitudinal percentage of vertebra-like stacks compared to the whole length of the device, and can reach over 90% in theory; the prototype was very close at 85% (242 W-hr/L).

In a battery designated for flexing, the long-term mechanical integrity is critical in addition to electrical performance. After repeated mechanical cycling, the battery was cut open to look for any changes in electrode materials or construction. The positive electrode was intact with no obvious cracking or peeling from the aluminum foil, confirming the mechanical stability of the design.

The researchers also continuously flexed and twisted the battery during discharge, but neither bending nor twisting interrupted the voltage curve. The voltage profile remained as expected even when the cell was continuously flexed and twisted during its entire discharge cycle.

Although the primary paper “Bioinspired, Spine-Like, Flexible, Rechargeable Lithium-Ion Batteries with High Energy Density,” published in the January 2018 issue of Advanced Materials is behind a paywall, its associated, highly detailed 12-page supporting material report (along with several videos) is not blocked. This supplement includes electrical and mechanical parameters, models, simulation results, details of cell construction, numerous microphotographs, and data graphs, plus specifics of the many electrical and mechanical tests, including tight static bends and dynamic fatigue flexing.

Sponsored Recommendations

Board-Mount DC/DC Converters in Medical Applications

March 27, 2024
AC/DC or board-mount DC/DC converters provide power for medical devices. This article explains why isolation might be needed and which safety standards apply.

Use Rugged Multiband Antennas to Solve the Mobile Connectivity Challenge

March 27, 2024
Selecting and using antennas for mobile applications requires attention to electrical, mechanical, and environmental characteristics: TE modules can help.

Out-of-the-box Cellular and Wi-Fi connectivity with AWS IoT ExpressLink

March 27, 2024
This demo shows how to enroll LTE-M and Wi-Fi evaluation boards with AWS IoT Core, set up a Connected Health Solution as well as AWS AT commands and AWS IoT ExpressLink security...

How to Quickly Leverage Bluetooth AoA and AoD for Indoor Logistics Tracking

March 27, 2024
Real-time asset tracking is an important aspect of Industry 4.0. Various technologies are available for deploying Real-Time Location.

Comments

To join the conversation, and become an exclusive member of Electronic Design, create an account today!